ceiling attic access panel

Titanium alloy with low carbon content is obtained because the carbon content remains the original concentration. The hardness of titanium alloy is mainly related to its carbon content. Therefore, after carburizing and subsequent heat treatment, the workpiece can obtain the performance of hard and tough inside. Galvanized wire varieties are mainly classified into three categories: electric galvanized wire, hot galvanized wire and galvanized wire. Among them, the classification of galvanized wire is divided into large roll galvanized wire, medium roll galvanized wire, small roll galvanized wire, galvanized shaft wire, truncated galvanized wire and other main production varieties.

In use, it can be well used to control its soft and hard degree in the annealing process, mainly used in the construction industry as a binding wire and binding line. Of course, its use is not limited to arts and crafts, but also widely used in the construction industry. Earlier woven lanterns were made of iron wire with appropriate candles placed inside. People hung them in front of their doors and looked very beautiful at night.

Post time: 27-07-22

The temperature of large roll galvanized wire should be controlled at 30 to 50℃ during electroplating. Because the chloride ions in the bath are very corrosive, quartz glass heaters are generally used. Continuous production does not need heating, but needs cooling. Cooling can be in the groove side row thin wall plastic pipe, through the flow of tap water cooling, can also be used as a titanium pipe temperature control device.

General material: electroplated low carbon steel wire

6. It’s easy for your dog to get used to a strange place as long as it has a home he’s familiar with, so you can take your dog on a trip instead of leaving him at home.

Pet cage from the use of material can be divided into plastic, wire, wire square tube, stainless steel four. General small animal cage multi-purpose is plastic and wire material, such as a lot of hamster cage, chinchilla cage are made of plastic or wire, small aquarium is plastic products, and the vast majority of small and medium-sized bird cage are wire products. The characteristics of this kind of small animal cage, is small, light, easy to carry, but also easy to clean care. For small animal cages, the wire diameter of the general iron wire is not very large, the thickness of the plastic is relatively thin, so the use of the time can not be “violent”, or the cage under the “destruction” will occur welding or plastic crack off.

Post time: 21-07-22

Post time: 25-08-22

3. Keep the rinse water clean after pickling the steel wire

The characteristics of these cages are small, light, easy to carry and easy to clean. For small animal cage, the wire diameter of the general iron wire is not very large, the thickness of the plastic is relatively thin, so the use of the time can not be “violence”, otherwise the cage in the “destruction” will occur under the welding or plastic crack.

Most of the production enterprises or large public places, they can play a defense hook mesh in the choice of time, often will hook mesh quality in position, so galvanized hook mesh this product few people are interested in, but does this show that galvanized hook mesh is not useful?

Heavy hexagonal mesh is made of low carbon steel wire galvanized large wire braided, the tensile strength of steel wire is not less than 38kg/m2, the diameter of steel wire can reach 2.0mm-3.2mm, the surface of steel wire is usually hot galvanized protection, galvanized amount can reach 500g/m2.

Bird cage is a kind of pet cage, is the main environment for ornamental birds to carry out activities and habitat, “work to do a good job, must first sharpen its tools” bird equipment is applicable or not, is one of the key to raise ornamental birds. Therefore, only if the appropriate cage and other accessories are prepared first, can the birds be kept healthy and lively, singing freely and suitable for viewing. There are many kinds of cages, depending on their body shape and habits.

Twisting the barbed wire: twisting the barbed wire in the opposite direction of the main wire. That is, it’s not twisted in one direction. This is called the twisted cord.

Post time: 11-06-24

Post time: 24-10-22

Barbed wire is used to make barbed wire, in part, to prevent livestock theft, because the surface is covered with sharp spikes that make it very difficult to penetrate through the barbed wire. On the other hand, it is because livestock generally have the habit of charging, and the barbed rope is used to circle, which makes livestock dare not rush to charge the barbed rope, thus saving the user’s use cost.

If the solder joint is too deep, it is not good, although the welding is more solid, but the bearing capacity of the solder joint is greatly reduced, once the pressure exceeds the load range, it will fracture at the solder joint, so it is more dangerous to use. Large galvanized wire production process of low carbon steel wire cleaning cleaning agent, should have no effect on the binding force of the coating, no corrosion of low carbon steel wire. Production process, acid activation acid activation liquid, should be able to remove the surface of low carbon steel wire corrosion products, oxide film, no corrosion to the matrix.

The galvanized requirements of the parts to be plated: the surface of the parts to be plated should be smooth, and there is no dirt that cannot be removed by pickling method. Such as paint, grease, cement, asphalt and excessive rotten harmful substances; All welds of welded components shall be sealed without air; Pipe fittings and containers must have exhaust and zinc inlet holes; The workpiece should be finished welded steel pipe without thread, if any thread should be protected.

Dip is one of the anticorrosion methods of galvanized diamond net. For hook mesh immersion is one of the methods of anti-corrosion, now the domestic more mature method is: powder immersion method, it originated from the fluidized bed method, the so-called fluidized bed is used in the Winkler gas furnace on the oil contact decomposition, and then developed the solid-gas two-phase contact process, gradually used in metal coating. So sometimes it is still called “fluidized bed coating method”, the actual process is to add the powder coating to the bottom of the porous, breathable container, the blower from the bottom into the treated compressed air, so that the powder coating turned to the “fluidization state”. It becomes a fine, evenly distributed powder.

That said, it can always deform by pulling hard without changing its integrity, so cold drawing has usually reached a limit, which is not a problem, because without this property it increases hardness, which is the desired effect. Cold wire drawing encountered more rain, when the climate is wet, easy oxidation and rust. Therefore, in the storage process should pay attention to avoid rust.

1. Electroplating process control

With the progress of the anti-corrosion skills of the cattle fence, the steel wire function of the cattle fence will also improve, so that the life of the progress of the use of great help. The number of years of use is primarily dependent on the environment of use and whether the operation of the construction is standard at the time. The operation standard of progress operation can also extend the number of years of use. The above is a general estimate of the life of the cattle net, I hope to help you.

The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.

Because of the high carbon content, simple cracks occur during water quenching, so double liquid quenching (water quenching + oil cooling) is mostly used, and oil quenching is mostly used for small cross section parts. This type of steel is generally used after quenching by medium temperature tempering or normalizing or in the surface quenching state. Mainly used for manufacturing spring and wear-resistant parts.