ceiling grid light fixtures

The advantages of hexagonal net to do jet hanging net, the first is that the processing speed is fast, the cost is low, and it is very good to roll out when it is open because of the edge. Common specifications: 12 cm x15 cm (11cm x11 cm) 11 cm x15 cm (10 cm x10 cm) 10 cm x12 cm (9 cm x9 cm) 9 cm x13 cm (9 cm x9 cm) 8 cm x10 cm (7 cm x7 cm) common wire: 1.3mm 1.4mm 1.5mm 1.6mm 1.7mm 1.8mm 2.0mm 2.3mm 2.5mm Commonly used materials: galvanized wire hot dip galvanized wire to wire drawn zinc aluminum alloy plastic coated wire stainless steel wire.

Post time: 18-05-23

After annealing, the wire will become soft, flexibility will increase, iron is a relatively active metal, and more active than hydrogen, so it is a good reducing agent. At room temperature, iron is not easy to react with oxygen, sulfur, chlorine and other non-metallic elements in dry air. Its production cost is lower, its use and scale are also relatively wide, and it has better protective function. Therefore, it is an important material for steel parts in strict working environment.

The production process of stainless steel blade barbed wire is basically similar to that of galvanized blade barbed wire, and the blade size is usually determined according to the mold.

There are 7 to 8 circles between the two thorns of the front and back twist barbed wire, while the ordinary barbed wire only has 3 and a half circles, which is neat and beautiful.

The production process of large rolls of galvanized wire is a level of drawing, through the mold into a slightly smaller diameter than the original. And so on down to the desired length. One pull is not desirable, must be numbered, from coarse to fine is dependent on metal ductility. If it changes too much it just breaks. After drawing to a certain diameter, galvanized, so that the finished product.

Cold galvanized, generally speaking, do not need heating, galvanized amount is little, this galvanized parts are easy to fall off in wet environment. Hot dip galvanizing, also known as hot dip galvanizing, is to melt the zinc ingot at high temperature, put some auxiliary materials in, and then dip the metal structural parts into the galvanized groove, so that the metal members are attached to a layer of zinc layer. The advantage of hot dip galvanized is that its anticorrosion ability is strong, the adhesion and hardness of galvanized layer is better.

Product features: strong structure, flat surface, with good corrosion resistance, oxidation resistance.

And high quality data and production cost and production conditions are bound, so some welding screen manufacturers did not meet the requirements of this aspect, natural in this case there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.

The difference between them can be so divided, the amount of zinc on the surface of the high zinc thorn rope is about 5 times that of the general zinc thorn rope, which greatly extends the time of rust prevention ability. In the appearance of the two products are silver and white at the same time the metal texture is better, for the difference between the two products if it is not good to distinguish, but for long-term work experts can be able to distinguish the two at a glance.

Bridge protection system generally do not need to be specially installed special drainage system, the use of hexagonal mesh made of gabion mesh boxes, the inside of the filler are selected stones, these stones are not easy to wear, and between the stones and stones will retain some gaps, so it is very good to meet the drainage requirements.

Cold galvanizing (galvanizing) is in the plating tank after the current unidirectional, so that the zinc gradually plated on the metal surface, slow production speed, uniform coating, thin thickness, usually as long as 3-15g, bright appearance, poor corrosion resistance, usually a few months will rust. Compared with hot dip galvanizing, the production cost of electric galvanizing is lower.

ceiling grid light fixtures

Applications in Construction

To keep the access panel closed and secure, install a latch or magnetic catch on the opposite side of the hinges. This will prevent the panel from accidentally opening and ensure it remains firmly in place when not in use.

- Moisture-Resistant Solutions In areas prone to humidity, such as bathrooms and kitchens, moisture-resistant laminated gypsum boards can help prevent mold and mildew growth.

Conclusion

Energy Efficiency: Mineral Fiber Tiles Ceiling is designed to improve energy efficiency by reducing the amount of heat that escapes through the ceiling.

Common Materials Used in Grid Ceilings

Performance is important!

Performance is important!

Conclusion

Popular tags

Popular on the whole site

Popular articles

What Is the Acoustic Ratio of Mineral Fiber Ceiling?