insulated ceiling access panel

The temperature of large roll galvanized wire should be controlled at 30 to 50℃ during electroplating. Because the chloride ions in the bath are very corrosive, quartz glass heaters are generally used. Continuous production does not need heating, but needs cooling. Cooling can be in the groove side row thin wall plastic pipe, through the flow of tap water cooling, can also be used as a titanium pipe temperature control device.

Post time: 20-06-22

Hot plating wire can generate thicker coating, and there are both pure zinc layer and iron zinc alloy layer, so the corrosion resistance is better. The production power of hot dip galvanizing is particularly high, and the duration of the parts in the hot dip galvanizing tank usually does not exceed lmin. Compared with galvanizing, hot-dip galvanizing has lower production cost and less environmental impact than galvanizing. To plate, tape, wire, tube and other profiles plating, automation degree is higher.

Galvanized wire in acid, alkali, sodium chloride aqueous solution of poor corrosion resistance, in the atmosphere containing carbon dioxide and hydrogen sulfide, as well as Marine atmosphere is not corrosion resistance. In high temperature and high humidity air and containing organic acid atmosphere is small, galvanized layer is also easy to be corroded. Galvanized wire and general wire is very different, general wire is cheap, and because the iron is not very stable, easy to rust in the wet place, so the stability is not very good, the life is not very long.

Hot dip galvanizing, also known as hot dip zinc, is the method of forming a layer of zinc coating on the surface of the workpiece after oil removal and rust removal, showing a clean and infiltrating surface, immediately immersed in the plating tank of zinc melting in advance. Cold galvanizing is the same after the removal of oil, in addition to lure, showing no pollution, infiltration of the workpiece hung into a special electroplating tank on the cathode, the anode with zinc. Switch on the DC power supply, zinc ions on the anode migrate to the cathode, and discharge on the cathode, so that the workpiece is coated with a layer of zinc layer hot dip galvanizing method.

The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.

Post time: 15-08-22

1. Grid structure is simple, beautiful and practical; 2. Easy to transport, installation is not limited by terrain relief; 3. Especially for mountain, slope, multi-curved area adaptability; 4. Medium low price, suitable for large area use. Main market: railway, highway closed net, yard fence, residential guardrail, all kinds of isolation net.

Post time: 28-10-22

Because of the high carbon content, simple cracks occur during water quenching, so double liquid quenching (water quenching + oil cooling) is mostly used, and oil quenching is mostly used for small cross section parts. This type of steel is generally used after quenching by medium temperature tempering or normalizing or in the surface quenching state. Mainly used for manufacturing spring and wear-resistant parts.

Compared with other galvanizing processes, galvanized steel wire has low cleaning requirements before plating. However, under the current trend of increasing the quality level of galvanized layer, some pollutants brought into the plating tank are obviously harmful. Because cleaning galvanized coating wastes a lot of time and reduces production, it is very important to properly clean and effectively rinse the substrate before electroplating.

The quality of hot-dip galvanized barbed wire is only good in the surface of the wire attached to the galvanized layer, and with the chemical reaction, the surface of the zinc layer will gradually lose effect because of the oxidation reaction, this situation is more prominent in the humid area of the environment. And because after all, it is rusty iron wire, so the quality of hot-dip galvanized barbed rope is certainly not up to the level of stainless steel barbed rope.

The most obvious gap in a short period of time is the cross section of this piece, hot dip galvanized wire because it is surface anti-corrosion treatment, so in the cross section of this piece will appear rust, and stainless steel wire because the internal raw materials and surface raw materials are consistent, so there is no such situation.

Most cattle netting is mechanically woven from highly malleable and corrosion-resistant mild steel wire or PVC coated steel wire. Several commonly used raw materials for the manufacture of cattle net are electrogalvanized wire, hot-dip galvanized wire, Galfan steel wire, ten percent aluminum zinc alloy steel wire and the new type of selenium chromium steel wire.

Post time: 23-11-22

3. Quality test report

The best way to manage off-road safety is to carry out management and protection from the source, maximize the safety of people’s lives and property, and reduce the non-operational costs of railway enterprises, which is a key content of railway safety work in the new era. At this time, it is necessary to install protective nets on both sides of the railway, which is what we usually say, blade barbed rope protective nets, which can prevent accidents.

Stainless steel blade barbed rope production process is basically similar to galvanized blade barbed rope production process, usually according to the mold to determine the size of the blade.