grid mount ceiling tiles

Now the pet cage on the market is still mainly wire cage, so the identification of wire cage mainly has the following parameters:

1, barbed rope protection net center line along the road within the land boundary 20 to 50 cm set.

1, stress relief before plating where the maximum tensile strength is greater than 1034Mpa key and important parts before plating should be at 200±10℃ stress relief for more than 1 hours, carburizing or surface quenching parts should be at 140±10℃ stress relief for more than 5 hours.

Carbon spring steel wire current national and occupational recommendation specifications are divided into two types: one is cold deformation steel wire, also known as cold tension spring steel wire. Cold drawn carbon spring steel wire is first quenched by lead to obtain soxhlet arrangement, and then the surface phosphating, with a large surface reduction rate drawn to the finished scale, the steel wire arrangement is fibrous, has high tensile strength and elastic limit, good winding and change function.

Every part of the plating can be zinc plated, even in dents, sharp corners and hidden places can be fully maintained. The cost of hot dip galvanized rust prevention is lower than that of other paint coatings. The galvanizing process is more convenient than other coating construction methods, and can prevent the time required after the device is painted on the site. In suburban environment, the standard hot-dip galvanized rust prevention thickness can adhere to more than 50 years without repair. In urban or offshore areas, the standard hot-dip galvanized rust protection layer can last 20 years without repair.

Post time: 04-01-23

During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.

The size of the dog cage is generally relatively small, suitable for indoor small dogs, dog cage is easy to carry, go out to compare the use, folding dog cage high strength steel wire and steel pipe material, the outer layer spray treatment. Strong texture, excellent rust resistance, the dog cage inside the tray, can be pulled out, convenient to clean the dog’s urine and feces, folding, dog cage is suitable for families and pet stores to raise more pet dogs.

With the increasing use of hook mesh, the method of bridge rail is also different. The height of the outer railing of the walkway or seat belt should not be lower than 1.10 meters. The net distance between railings should not be greater than 140 mm and horizontal bar rails should not be used. The planning of the hook mesh is necessary to be safe and reliable, the bolt should be installed on the basis of the railing, its strength should meet the requirements of the standard.

Cages are more often used for large dogs, which have a lot of strength. The crate must be strong, or the dog will easily break out of the crate.

We must have a certain understanding of the hexagonal net, we are swayed by the beautiful shape of the hexagonal net, not only the shape of the hexagonal net is very beautiful, in fact, the practical value of survival is very high. Hexagonal mesh of all kinds of guardrail, the value of the highway is more prominent, it is not only used in a variety of roads, in a variety of sports ball venues and landslides try to take care of, but also to reach a very close utility.

Post time: 02-09-22

Post time: 11-10-22

Therefore, when zinc reaches saturation in the solid melt, the two elements of zinc and iron atoms diffuse with each other, and the zinc atoms diffused into (or infiltrated into) the iron matrix migrate in the lattice of the matrix and gradually form an alloy with iron, while the iron diffused into the molten zinc liquid forms an intermetallic compound FeZn13 with zinc and sinks into the bottom of the hot-dip galvanized pot, that is, zinc slag. When the workpiece is removed from the zinc leaching solution, the surface of the pure zinc layer is formed, which is hexagonal crystal, and its iron content is not more than 0.003%.

Application scope of hot wire: Because the coating is thicker, hot galvanized has better protective performance than electric galvanized, so it is an important protective coating for steel parts used in harsh working conditions. Hot galvanized products in chemical equipment, petroleum processing, ocean exploration, metal structure, power transmission, shipbuilding and other industries have a wide range of applications, in the agricultural field such as pesticide irrigation, greenhouse and construction such as water and gas transmission, wire casing, scaffolding, bridge, highway guardrail and other aspects, in recent years has been widely used.

There are still some differences between the welding mesh and the wire mesh and the steel mesh. This mesh is mainly a welding mesh made of high quality low carbon steel wire straightened and cut, and then welded with electric welding equipment. It can be said that because of the characteristics of fast production and convenient transportation, it has been applied to many industries. The application of welding mesh in the industry, because the mesh has strong corrosion resistance and uniform mesh. It has become a special grid for floor heating in the building industry and has been applied in many fields.

Custom is made of low carbon steel silk woven, mesh structure he has the characteristics of corrosion resistance, high strength and ductility. Steel wire diameter up to 2.0mm-4.0mm, steel wire appearance is usually selected hot dip galvanized maintenance, galvanized maintenance layer thickness can be made according to customer needs, galvanized maximum can reach 300g/㎡.

National standards on the use of wire mesh standards have certain requirements, diameter and mesh size matching use, rather than simply diameter size, on the plaster layer to use is mesh should not be greater than 20×20, diameter is not easy to be less than 1mm, light selection diameter is not much significance, choose 40×40×0.9 and choose 10×10×0.6 wire mesh, Which one is better? 10×10×0.6, I’m afraid.

The management system of the rinsing water after wire pickling should be discharged regularly and regularly, and the rinsing water should be kept clean and low acid value as far as possible. It is more appropriate to control the pH value of 3. The concentration of plating aid should not be too high. The hot plating wire must be added with ammonium chloride and zinc chloride according to the data of laboratory analysis, and the specific gravity of the composite solution is controlled within the range of 50~80g/L. If ammonium chloride or zinc chloride is added without reference to the results of laboratory analysis, it should be criticized and educated, and economic treatment should be given if necessary.